Concrete for a 10×10 slab

What a 10×10 slab is usually for

• Bistro-set patio
• Medium shed
• Hot tub pad with a step-off
• Basketball key / practice pad

A 10×10 is the classic first concrete project — big enough to feel like a real patio, small enough that a mistake is affordable. It comfortably takes a small table and two chairs, or a grill with standing room, but it is tight for a six-seat dining set: allow 3 feet of clearance behind each chair and a 10 foot side disappears quickly.

Bags or a truck for this 10×10 patio

At 1.23 cubic yards, this slab sits in the awkward middle band where the short-load fee decides it. Here is the comparison with the fees included:

Ready-mix is the better call at this size, even carrying the short-load fee. Beyond the price, a truck delivers the whole slab as one continuous placement — no cold joints between batches, no risk of the first section setting while you mix the last, and a consistent mix throughout. Mixing 62 bags to match it is a full day of heavy work with a worse result.

The short-load fee is what people miss. Suppliers charge it below roughly 4 cubic yards, typically $50–$150, because sending a truck out costs them the same whether it is full or not. Always ask for the delivered total including fees rather than the per-yard rate. The full reasoning is in bags vs ready-mix concrete.

Control joints so a 10×10 patio cracks where you choose

Concrete shrinks as it cures and it will crack — the only question is whether it cracks where you decided or where it chose. Control joints are the decision. The rule of thumb is a maximum spacing in feet of about two to three times the slab thickness in inches, so at 4″ that is 8–12 ft.

At 10×10 this slab fits inside a single panel at the maximum allowed spacing, so the rule does not force any joints on you. That said, a hard-freeze climate or a subgrade you are not confident about is a good reason to cut one anyway — a tooled joint disappears within a season, whereas a random shrinkage crack is permanent. The sequence is in forming and pouring a small slab.

How thickness changes a 10×10 slab

Thickness is the one input that changes the order most, and it is chosen by what will sit on the slab rather than by budget. Here is the same 100 sq ft footprint at each common depth:

Going from 4″ to 6″ on this slab adds roughly $124 in materials — about 50% more. That is the entire cost of the decision, and it is why the advice for anything carrying a vehicle is to just pour the extra inches. Removing and replacing a cracked slab costs many times the difference.

The 3.5″ row is not a recommendation, it is a reality check: a “4 inch” slab poured on a subgrade that is a little high in places genuinely finishes at 3.5″ in those spots. If your base is not dead flat, order to the thicker figure. More on this in concrete slab thickness: 4″ vs 6″.

Pouring a 10×10 patio: the practical plan

Be honest about that number.62 bags is past the point where a one-person mix-and-pour produces a good slab. Concrete starts stiffening within about 30 to 60 minutes in warm weather, so a long mixing session leaves cold joints between what you placed first and what you placed last — visible lines that are also weak lines. If you are set on bags, get help and run two mixers; otherwise price the truck.

Budget for the tools as well as the concrete: a mixer runs about $70/day, a plate compactor for the base about $80/day, and a concrete saw for the joints about $60/day.

What it would cost to hire out

A professionally installed basic slab runs roughly $4–$8 per square foot including labour, so for 100 sq ft:

The gap is labour, and it is real — but so is the risk transfer. A contractor who gets the finish wrong fixes it; if you do, you own it. See DIY vs hiring a pro and slab cost by size for the full breakdown of where each route makes sense.

Watch out on a slab this size

This size crosses the threshold where ready-mix becomes worth pricing. The bag count below is genuinely a lot of bags to mix, and the ready-mix figure is barely above a supplier's minimum load — so the honest comparison has to include the short-load fee, not just the per-yard price.

The arithmetic

Volume = 10 × 10 × (4 ÷ 12) = 33.33 ft³, then ÷ 27 = 1.23 cubic yards. An 80 lb bag yields 0.60 ft³, so 33.33 ÷ 0.60 = 56 bags before waste; add 10% and round up to 62 bags. Ready-mix rounds up to the quarter yard, giving 1.5 yd³. Every constant behind those steps is documented in how we calculate, and the reasoning is in how much concrete do I need?

Other slab sizes

• Concrete for a 8×8 slab
• Concrete for a 8×10 slab
• Concrete for a 8×12 slab
• Concrete for a 10×12 slab
• Concrete for a 10×16 slab
• Concrete for a 10×20 slab
• Concrete for a 12×12 slab
• Concrete for a 12×14 slab

See all slab sizes →